Effect of hardness and composition gradients on Barkhausen emission in case hardened steel

The effect of gradients in hardness, structure and composition in the surface layers on magnetic Barkhausen noise (MBN) was investigated in two widely used low alloy steels. One material was case hardened by induction hardening. The other was case carburised. Similar hardness profiles were produced by the two treatments. It was found that the variation in structure and hardness through the case in the induction-hardened steel had a minor effect on the MBN profile. In contrast, the inhomogeneity in the case-carburised material showed up clearly. This took the form of a broadened or two-peak MBN profile. When the surface layer containing the case was removed by etching, the broadened profile was replaced by a profile with a single peak. It is concluded that the shape and position of the MBN profile is significantly affected when a gradient in microstructure is induced by a gradient in carbon content. On the other hand, a gradient in microstructure induced by heat treatment with a constant carbon level has much less affect on the MBN profile for the induction-hardened steel.     

Influence of chemistry and hot rolling conditions on high permeability non-grain oriented silicon steel

This paper discusses the influence of chemical composition on the final electromagnetic properties in higher permeability material. Furthermore, the effect of the hot rolling practice and the end of austenite transformation temperature range on the hot band microstructure is described. The magnetic polarization J₅₀₀₀ better than 1.7 T, using hot rolling conditions 40 mm transfer bar thickness, finish mill entry temperature 1000 °C, and finishing temperature 800–840 °C and after decarburization heat treatment and grain growth treatment, was obtained.     

微合金钢中稀土对沉淀相和性能的影响

在Nb(Ti,V）微合金钢中，主要沉淀相分别为Nb(C,N),(Nb,Ti)(C,N)和V（C，N）。稀土降低沉淀相完全溶解的温度，增大奥氏体中沉淀相析出的孕育期，降低析出速率，抑制奥氏体中沉淀相的析出，在铁素体相区，稀土提高沉淀相的析出速率和数量，促进沉淀相的析出，其中稀土对铌沉淀相析出的作用影响最强。锻态钢中，稀土有促进细化球化析出相的作用，随稀土含量增加，沉淀相析出数量增加，但过量稀土，促进作用又减弱，稀土在保持微合金钢强度的情况下，显著改善其冲击韧性，尤其是低温韧性，微合金钢中添加适量稀土可获得更佳的综合性能。     

Dynamic electrochemical impedance spectroscopy measurements of passive layer cracking under static tensile stresses

Electrochemical impedance spectroscopy allows the examination of corrosion susceptibility and resistance for different construction materials, in particular the determination of the properties of their passive films. This technique makes possible the analysis of electrochemical processes in time domain, including rapid phenomena such as changes in the properties of passive films, but it has never been used for passive layer cracking examination. In many cases, fracture of the passive film under tensile stresses leads to stress corrosion cracking. Therefore, investigations of passive layer cracking on austenitic stainless steels under tensile stresses facilitate the understanding of the mechanism of stress corrosion cracking in these common engineering materials. The effect of static tensile stresses on the passive film cracking behaviour of type 304L stainless steel immersed in 0.5 M NaCl solution at room temperature has been investigated. This paper presents the impedance spectra obtained for 304L stainless steel samples at different potential values.Contribution to the 3rd Baltic Conference on Electrochemistry, Gdansk-Sobieszewo, Poland, 23–26 April 2003Dedicated to the memory of Harry B. Mark, Jr. (28 February 1934–3 March 2003)     

Die Isolierung radioaktiv markierter nichtmetallischer Einschlüsse aus Hochlegierten Stählen

Zur Isolierung von Einshlüssen aus hochlegierten Stählen werden die Hauptkomponenten Fe, Ni, Cr und weitere Metalle durch mehrstufig ausgeführte Flüssig-Flüssig-Extraktionen mit verschiedenen Extraktionsmitteln abgetrennt. Die im Eindampfrückstand der wäβrigen Phase nach der Extraktion verbleibenden Einschlüsse können für die meisten Radionuklide ohne nennenswerte Selbstabsorption mit einem Groβflächenzählrohr oder anderen geeignetenZählvorrichtungen ausgemessen werden.     

XPS study of Cr segregation in a martensitic stainless steel

Cr martensitic steels are promising materials for structural applications in future nuclear fusion reactors. Because the embrittlement after tempering treatments can be a serious problem, the fracture mode of a steel with 10.5 wt% of Cr treated at 700°C for 18 h has been investigated through Charpy tests in the temperature range from −100°C to +150°C. X-ray photoelectron spectroscopy (XPS) analyses carried out on the fracture surfaces evidenced the segregation of Cr in both ductile and brittle (quasicleavage) fields. The unexpected result indicates that Cr segregation weakens the atomic bonds; thus, the fracture path in both the cases corresponds to the zones with higher Cr content.     

TEM investigation of the formation mechanism of deformation twins in Fe–Mn–Si–Al TWIP steels

The microstructure of a Fe–Mn–Si–Al twinning-induced plasticity (TWIP) steel exhibiting remarkable work hardening rate under uniaxial tensile deformation was investigated using transmission electron microscopy to uncover the mechanism(s) controlling the nucleation and growth of the mechanically induced twins. The results show that the stair-rod cross-slip deviation mechanism is necessary for the formation of the twins, while large extrinsic stacking faults homogenously distributed within the grains could act as preferential sources for the activation of the deviation process. The influence of such features on the thickness and strength of the twins and the resulting mechanical behaviour is discussed and compared to similar works recently performed on Fe–Mn–C TWIP steels.     

Orientation relationship in Eurofer martensitic steels

Both TEM and SEM/EBSD orientation measurements are carried out on a Eurofer97 martensitic steel. The influence of the prior austenitic grain size is studied using dedicated heat treatments. The intra laths misorientation is estimated by TEM. SEM/EBSD orientation mapping enable to study the actual orientation relationship (OR) between the parent austenitic phase and the martensitic phase. Neither the Nishiyama–Wasserman nor the Kurdjumov–Sachs OR is able to account for both the misorientation angle distributions, the pole figure and the misorientation axes measured. The mixed OR recently proposed by Gourgues et al. (Electron backscattering diffraction study of acicular ferrite, bainite, and martensite steel microstructures, Mater. Sci. Tech. 16 (2000), pp. 26–40.) and Sonderegger et al. (Martensite laths in creep resistant martensitic 9–12%Cr steels – Calculation and measurement of misorientations, Mater. Characterization (2006), in Press.) seems to be able to account for most of these results. Based on this OR, a new angular criterion is proposed to detect blocks of laths.     

Colloidal Analysis of Particles Extracted from Microalloyed Steels

Different colloidal particle characterization methods are examined for their suitability to determine the particle size distribution of particles extracted from steels. Microalloyed steels are dissolved to extract niobium and titanium carbonitride particles that are important for the mechanical properties of these steels. Such particles have sizes ranging from several nanometers to hundreds of nanometers depending on the precipitation stage during the thermomechanically controlled rolling process. The size distribution of the particles is analyzed by dynamic light scattering (DLS), analytical ultracentrifugation (AUC), and hollow fiber flow field-flow fractionation (HF5) and compared to data obtained for reference particles as well as data from electron microscopy, the standard sizing technique used in metallurgy today. AUC and HF5 provide high-quality size distributions, average over large particle numbers that enables statistical analysis, and yield useful insights for alloy design; however, DLS fails due to a lack of resolution. Important aspects in the conversion and comparison of size distributions obtained for broadly distributed particle systems with different measurement principles and the role of surfactants used in sample preparation are discussed.     

Relaxation mechanism of rotational type in fracture of weld joints for austenic steels

Studied is the mesoscale behavior of plastic deformation and fracture of weld joints for austenic steels. Large-scale rotational modes of deformation in heat affected zones are identified with the first stage of formation of band structures; it is related to the “traveling neck” phenomenon in the base metal. The second stage is connected with crack generation and the state of affairs in the heart-affected zone.